|
A ship's wheel or boat's wheel is device used aboard a water vessel to change that vessel's course. Together with the rest of the steering mechanism, it forms part of the helm. It is connected to a mechanical, electric servo, or hydraulic system which alters the vertical angle of the vessel's rudder relative to its hull. In some modern ships the wheel is replaced with a simple toggle that remotely controls an electro-mechanical or electro-hydraulic drive for the rudder, with a rudder position indicator presenting feedback to the helmsman. Prior to the invention of the ship's wheel the helmsman relied on a tiller— a horizontal bar fitted directly to the top of the rudder post— or a whipstaff— a vertical stick acting on the arm of the ship's tiller. A typical ship's wheel is composed of eight cylindrical wooden spokes (though sometimes as few as six or as many as ten) shaped like balusters and all joined at a central wooden hub or ''nave'' (sometimes covered with a brass ''nave plate'') which housed the axle. The square hole at the centre of the hub through which the axle ran is called the ''drive square'' and was often lined with a brass plate (and therefore called a ''brass boss'', though this term was used more often to refer to a brass hub and nave plate) which was frequently etched with the name of the wheel's manufacturer. The outer rim is composed of four sections each made up of stacks of three ''felloes'', the ''facing felloe'', the ''middle felloe'', and the ''after felloe''. Because each group of three felloes at one time made up a quarter of the distance around the rim, the entire outer wooden wheel was sometimes called the ''quadrant''. Each spoke ran through the middle felloe creating a series of handles beyond the wheel's rim. One of these handles/ spokes was frequently provided with extra grooves at its tip which could be felt by a helmsman steering in the dark and used by him to determine the exact position of the rudder—this was the ''king spoke'' and when it pointed straight upward the rudder was believed to be dead straight to the hull. The completed ship's wheel and associated axle and pedestal(s) might even be taller than the person using it. The wood used in construction of this type of wheel was most often either teak or mahogany, both of which are very durable tropical hardwoods capable of surviving the effects of salt water spray and regular use without significant decomposition. The steering gear of earlier ships's wheels sometimes consisted of a double wheel where each wheel was connected to the other with a wooden ''spindle'' that ran through a ''barrel'' or ''drum''. The spindle was held up by two ''pedestals'' that rested on a wooden ''platform'', often no more than a grate. A ''tiller rope'' or ''tiller chain'' (sometimes called a ''steering rope'' or ''steering chain'') ran around the barrel in five or six loops and then down through two ''tiller rope/ chain slots'' at the top of the platform before connecting to two sheaves just below deck (one on either side of the ship's wheel) and thence out to a pair of pulleys before coming back together at the tiller and connecting to the ship's rudder. Movement of the wheels (which were connected and moved in unison) caused the tiller rope to wind in one of two directions and angled the tiller left or right. In a typical and intuitive arrangement, a forward-facing helmsman turning the wheel ''counter''clockwise would cause the tiller to angle to starboard and therefore the rudder to swing to port causing the vessel to also turn to port (see animation).〔 On many vessels the helmsman stood facing the rear of the ship with the ship's wheel before him and the rest of the ship behind him— this still meant that the direction of travel of the wheel at its apex corresponded to the direction of turn of the ship. File:Britannia Yacht Club Commodore Boardroom.jpg|Britannia Yacht Club's Commodore Boardroom features a ship's wheel table File:Annunciator.jpg|USS ''LST-325'' ship's wheel and engine order telegraph File:US Navy 050823-N-9076B-001 Electrician's Mate 1st Class Aaron Walker speaks to chief petty officer selectees as he stands at the helm of USS Constitution in Boston.jpg|U.S. Navy personnel aboard the USS Constitution, by the ship's wheel ==References== 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「ship's wheel」の詳細全文を読む スポンサード リンク
|